Next you can calibrate your filament as usual, and second extruder offset if you have.įor information on upgrading from or reverting to stock FW and other procedures please check Da Vinci Voltivo forum.When update is complete you must calibrate your bed height!Use manual bed leveling in menu.After printer restarted do not forget to send G-Code M502 then M500 from repetier's Print Panel tab or from the printer menu "Settings/Load Fail-Safe" and accept to save the new eeprom settings.If you have black bars and printer is not detected properly, it means you did not do the point 4 properly ( #172) so go back to point 4. If done correctly you will see the arduino sketch compile successfully and output in the log showing the upload status. Press the usual arduino compile and upload button.NOTE: You can usually find this out by looking at the tools -> port menu both before and after plugging in the printer to your computer's USB. Under the tools menu select the board type as Arduino DUE (Native USB Port) and the proper port you have connected to the printer.Modify the DAVINCI define in Configuration.h file to match your targeted Da Vinci.Open the project file named repetier.ino located in src\ArduinoDUE\Repetier directory in the arduino IDE.NOTE: You do not need to compile arduino from source these files are in the arduino directory structure FAQ#114. Update variants.cpp/USBCore.cpp arduino files with the ones present in src\ArduinoDUE\AdditionalArduinoFile according your IDE version.Do not use 1.5.8 it is not supported and will give compilation error: FAQ#201 Use an arduino IDE supporting arduino DUE, 1.8.0 with Due 1.6.8 module from board manager FAQ#166.Note 2: remove the jumper before flashing if still there Note : points 1 and 2 are only needed to wipe the stock fw or a corrupted fw, for update they are not necessary. NOTE: Windows users may need to install drivers to detect the board. The machine will have been flashed removing the current stock firmware and allowing it to be detected as a normal arduino DUE. Turn the machine on and wait a few seconds then turn it off again.Some Boards do not have jumper pins exposed but can still be shorted with a conductive wire. With the machine off remove the back panel and short the jumper JP1 or J37 depending on model.The previous version (based on repetier v0.91) can be found here The current firmware is based on repetier Firmware 0.92 : bgm370 Da Vinci 1.0 FW You can find more info on the Voltivo forum. It allows the use of clear ABS (by disabling optical sensors), as well as other arbitrary filament brands/types as temperatures can be controlled freely and there is no requirement for chiped cartridges.It works stand alone (not connected to PC) if you use a WIFI SD Card or SD card extender.giving you full control of your hardware. It works with host software such as repetier host and OctoPrint, cura, Simplif圓D, etc.Here are just a few of the benefits of using this firmware: More info can be found on the Voltivo forum. Supported boards have a jumper labeled JP1, second generation boards have a jumper labeled J37. The board can be easily exposed by removing the back panel of the printer secured by two torx screws. When it is possible on 1.0/2.0, currently on 1.0A/2.0A and AiO there is no way to revert to stock fw so be sure of what you are doing.ĪiO scanner support is present in FW but scanner software support is currently basic, horus is a good candidat, feel free to help here YOU MIGHT DAMAGE YOUR PRINTER OR VOID YOUR WARRANTY, DO IT ON YOUR OWN RISK. If you change the board, currently DUE based are supported with RADDS, as well as Graphical screen and LCD with encoder, there are some sample configuration files provided for RADDS/DUE/GLCD using 1/128 step drivers. This firmware is based on the popular repetier firmware for Da Vinci 1.0/A, 2.0 single fan, 2.0/A dual fans and also AiO (NB:scanner function is not supported so AiO will work like an 1.0A) Do not use it on PRO or Jr or Miniīe noted original Repetier FW is not compatible wih Davinci boards From this I can get a good overview what is going on and who is blocking who.Da Vinci Firmware based on Repetier (0.92.10) This will output a dump of all threads running with functions. Just to warn you, I am very much a novice at linux (like, I need to refresh on how to copy files from the PI to my windows computer), but I'll do my best following these directions: If it happens again, I'll try your instructions from the other thread. I'm going to restore the printers from their backup config files and run another print job.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |